DellEMC PowerScale(Isilon)初始化配置
一、Isilon 存储硬件说明
内部交换机：Isilon使用25GB IP交换机做集群节点间的文件数据同步、数据拆分组合等。此次配置DellEMC S4112F-ON交换机两台。
外部网络交换机：提供前端服务器访问，要求为1Gige或10Gige网络。
Isilon存储节点：Isilon最新的产品线分为S系列、X系列、NL系列、EX系列和Accelerate备份加速器及Gen 6 A系列和H系列，本次实施为4节点A200。
二、实施准备
1.内部网络
每节点必须配置至少一个IP地址和子网掩码（内部/私有网络对外部网是不可见的）；如果希望配置内部冗余网络，则每节点需要两个或者更多IP地址用于冗余（不能与非冗余地址在一个子网内）；如果配置故障切换，则还需要一个Failover IP子网。分别为int-a、int-b、failover。
2.外部网络
1. 每节点必须配置至少一个IP地址和子网掩码(除非使用NANON—NANON即Not All Nodes On Network，非所有节点入网)；
2. 如果配置NFS Failover，则需要配置第二个外部网口IP地址（不能与第一个网口在同一个子网）和一个NFS Failover IP地址；
3. 配置SmartConnect 则需要的额外Service IP地址统一对外访问（与第一个网卡在同一子网）；
4. 另外根据客户需要配置DNS服务器、DNS域、默认网关
3.配置规划
三、实施步骤
1.连接拓扑和开机加电
Isilon 内部网络冗余拓扑
Isilon 加电需要双路电源和两块电池，如果任意节点上的电池出现故障，该节点将进入只读模式；Isilon加电后，按前面板的电源按钮方可启动Isilon节点。
2.连接串口
使用串口线连接Isilon，通过SecureCRT以如下配置访问Isilon：
*其中Port：选项根据管理机的实际情况选择
3.创建第一个节点
选择[1]创建一个新集群：
Please select an option.
Node build: Isilon OneFS v8.2.2.0 B_8_2_2_016(RELEASE)
Node serial number: SJWXNT183800289
[ 1] Create a new cluster
[ 2] Join an existing cluster
[ 3] Exit wizard and configure manually
[ 4] Reboot into SmartLock Compliance mode
Wizard >>> 1
阅读软件许可和维护协议，并接受
SOFTWARE LICENSE AND MAINTENANCE AGREEMENT
*** IMPORTANT INFORMATION - PLEASE READ CAREFULLY ***
This Software contains computer programs and other proprietary material and
information, the use of which is subject to and expressly conditioned upon
acceptance of this Software License and Maintenance Agreement (the
"Agreement").
…………
…………
Do you accept the EULA? [no] yes
输入root密码和admin密码：
Please change the root password from the default.
Please enter new password for root:
Please re-enter password for root:
Password changed.
Please change the admin password from the default.
Please enter new password for admin:
Please re-enter password for admin:
Password changed.
输入集群名：
Enter a new name for the cluster:
Configure name >>> Lxyy-isilon
Cluster name set to isilon
输入字符集：
Cluster encoding:
[ 1] Windows-SJIS
[ 2] Windows-949
[ 3] Windows-1252
[ 4] EUC-KR
[ 5] EUC-JP
[ 6] EUC-JP-MS
[ 7] UTF-8-MAC
[ 8] UTF-8
[ 9] ISO-8859-1 (Latin-1)
[10] ISO-8859-2 (Latin-2)
[11] ISO-8859-3 (Latin-3)
[12] ISO-8859-4 (Latin-4)
[13] ISO-8859-5 (Cyrillic)
[14] ISO-8859-6 (Arabic)
[15] ISO-8859-7 (Greek)
[16] ISO-8859-8 (Hebrew)
[17] ISO-8859-9 (Latin-5)
[18] ISO-8859-10 (Latin-6)
[19] ISO-8859-13 (Latin-7)
[20] ISO-8859-14 (Latin-8)
[21] ISO-8859-15 (Latin-9)
[22] ISO-8859-16 (Latin-10)
[Enter] Use current encoding: utf-8
Configure encoding >>> 8
Encoding set to utf-8
配置int-a
Configure interface int-a:
[ 1] Configure netmask
[ 2] Configure int-a IP ranges
[Enter] Keep the current configuration:
Netmask: (not set)
IP ranges: (not set)
Configure interface int-a >>> 1
Enter a new netmask
Configure int-a netmask >>> 255.255.255.0
Configure interface int-a:
[ 1] Configure netmask
[ 2] Configure int-a IP ranges
[Enter] Keep the current configuration:
Netmask: 255.255.255.0
IP ranges: (not set)
Configure interface int-a >>> 2
Configure int-a IP ranges
[ 1] Add an IP range
[ 2] Delete an IP range
[Enter] Keep the current IP ranges:
IP ranges: (not set)
Configure int-a IP ranges >>> 1
Enter the low IP address of the range to add:
Low IP address (add) >>> 10.0.0.1
Enter the high IP address of the range:
High IP address (add) >>> 10.0.0.254
Configure int-a IP ranges
[ 1] Add an IP range
[ 2] Delete an IP range
[Enter] Keep the current IP ranges:
IP ranges: 10.0.0.1-10.0.0.254
Configure int-a IP ranges >>> [Enter]
Configure interface int-a:
[ 1] Configure netmask
[ 2] Configure int-a IP ranges
[Enter] Keep the current configuration:
Netmask: 255.255.255.0
IP ranges: 10.0.0.1-10.0.0.254
Configure interface int-a >>> [Enter]
配置int-b
Select the internal interfaces to configure
[ 1] int-a - primary internal interface
[ 2] int-b - secondary internal interface (failover)
[Enter] Exit configuring internal interfaces
Configure internal interfaces >>> 2
Configure interface int-b (failover):
[ 1] Configure netmask
[ 2] Configure int-b IP ranges
[ 3] Configure failover IP ranges
[Enter] Keep the current configuration:
Netmask: (not set)
IP ranges: (not set)
Failover IP ranges: (not set)
Failover: disabled
Configure interface int-b (failover) >>> 1
Type a new netmask
Configure int-b netmask >>> 255.255.255.0
Configure interface int-b (failover):
[ 1] Configure netmask
[ 2] Configure int-b IP ranges
[ 3] Configure failover IP ranges
[Enter] Keep the current configuration:
Netmask: 255.255.255.0
IP ranges: (not set)
Failover IP ranges: (not set)
Failover: disabled
Configure interface int-b (failover) >>> 2
Configure int-b IP ranges
[ 1] Add an IP range
[ 2] Delete an IP range
[Enter] Keep the current IP ranges:
IP ranges: (not set)
Configure int-b IP ranges >>> 1
Enter the low IP address of the range to add:
Low IP address (add) >>> 10.0.1.1
Enter the high IP address of the range:
High IP address (add) >>> 10.0.1.254
Configure int-b IP ranges
[ 1] Add an IP range
[ 2] Delete an IP range
[Enter] Keep the current IP ranges:
IP ranges: 10.0.1.1-10.0.1.254
Configure int-b IP ranges >>> [Enter]
配置failover
Configure interface int-b (failover):
[ 1] Configure netmask
[ 2] Configure int-b IP ranges
[ 3] Configure failover IP ranges
[Enter] Keep the current configuration:
Netmask: 255.255.255.0
IP ranges: 10.0.1.1-10.0.1.254
Failover IP ranges: (not set)
Failover: disabled
Configure interface int-b (failover) >>> 3
Configure failover IP ranges
[ 1] Add an IP range
[ 2] Delete an IP range
[Enter] Keep the current IP ranges:
Failover IP ranges: (not set)
Configure failover IP ranges >>> 1
Enter the low IP address of the range to add:
Low IP address (add) >>> 10.0.2.1
Enter the high IP address of the range:
High IP address (add) >>> 10.0.2.254
Configure failover IP ranges
[ 1] Add an IP range
[ 2] Delete an IP range
[Enter] Keep the current IP ranges:
Failover IP ranges: 10.0.2.1-10.0.2.254
Configure failover IP ranges >>> [Enter]
Configure interface int-b (failover):
[ 1] Configure netmask
[ 2] Configure int-b IP ranges
[ 3] Configure failover IP ranges
[ 4] Disable failover
[Enter] Keep the current configuration:
Netmask: 255.255.255.0
IP ranges: 10.0.1.1-10.0.1.254
Failover IP ranges: 10.0.2.1-10.0.2.254
Failover: enabled
Configure interface int-b (failover) >>> [Enter]
Select the internal interfaces to configure
[ 1] int-a - primary internal interface
[ 2] int-b - secondary internal interface (failover)
[Enter] Exit configuring internal interfaces
Configure internal interfaces >>>[Enter]
配置外部地址
Configure external subnet
[ 1] mgmt-1 - External interface
[ 2] 10gige-1 - External interface
[Enter] Exit configuring external network.
Configure external subnet >>> 2
Configure interface 10gige-1:
[ 1] Configure netmask
[ 2] Configure MTU
[ 3] Configure 10gige-1 IP ranges
[Enter] Keep the current configuration:
Netmask: (not set)
MTU: 1500
IP ranges: (not set)
Configure interface 10gige-1 >>> 1
Enter a new netmask
Configure 10gige-1 netmask >>> 255.255.255.0
Configure interface 10gige-1:
[ 1] Configure netmask
[ 2] Configure MTU
[ 3] Configure 10gige-1 IP ranges
[Enter] Keep the current configuration:
Netmask: 255.255.255.0
MTU: 1500
IP ranges: (not set)
Configure interface 10gige-1 >>> 3
Configure external IP ranges
[ 1] Add an IP range
[ 2] Delete an IP range
[Enter] Keep the current IP ranges:
IP ranges: (not set)
Configure 10gige-1 IP ranges >>> 1
Enter the low IP address of the range to add:
Low IP address (add) >>> 192.168.12.60
Enter the high IP address of the range:
High IP address (add) >>> 192.168.12.71
Configure external IP ranges
[ 1] Add an IP range
[ 2] Delete an IP range
[Enter] Keep the current IP ranges:
IP ranges: 192.168.12.60-192.168.12.71
Configure 10gige-1 IP ranges >>> [Enter]
Configure interface 10gige-1:
[ 1] Configure netmask
[ 2] Configure MTU
[ 3] Configure 10gige-1 IP ranges
[Enter] Keep the current configuration:
Netmask: 255.255.255.0
MTU: 1500
IP ranges: 192.168.12.60-192.168.12.71
Configure interface 10gige-1 >>>[Enter]
配置网关地址
Enter default gateway:
Configure default gateway >>> 192.168.12.1
配置SmartConnect
Configure SmartConnect settings
[ 1] SmartConnect zone name
[ 2] SmartConnect service IP
[Enter] Keep the current SmartConnect settings:
SmartConnect zone name: (not set)
SmartConnect service IP: (not set)
Configure SmartConnect settings >>> 1
Enter SmartConnect zone name
SmartConnect zone name >>> isilon.lxyy.com
Configure SmartConnect settings
[ 1] SmartConnect zone name
[ 2] SmartConnect service IP
[Enter] Keep the current SmartConnect settings:
SmartConnect zone name: service.isilon.com
SmartConnect service IP: (not set)
Configure SmartConnect settings >>> 2
Enter SmartConnect service IP
SmartConnect service IP >>> 192.168.12.88
Configure SmartConnect settings
[ 1] SmartConnect zone name
[ 2] SmartConnect service IP
[Enter] Keep the current SmartConnect settings:
SmartConnect zone name: isilon.lxyy.com
SmartConnect service IP: 192.168.12.88
Configure SmartConnect settings >>> [Enter]
跳过DNS配置
Configure DNS settings
[ 1] DNS servers
[ 2] Search domains
[Enter] Keep current DNS settings:
DNS servers: (not set)
Search domains: (not set)
Configure DNS settings >>> 1
Enter a comma-separated list of DNS servers:
Configure DNS >>> 192.168.12.1
Configure DNS settings
[ 1] DNS servers
[ 2] Search domains
[Enter] Keep current DNS settings:
DNS servers: 192.168.12.1
Search domains: (not set)
Configure DNS settings >>> 2
Enter a comma-separated list of search domains:
Search domains >>> lxyy.com
Configure DNS settings
[ 1] DNS servers
[ 2] Search domains
[Enter] Keep current DNS settings:
DNS servers: 192.168.12.1
Search domains: lxyy.com
Configure DNS settings >>> [Enter]
Configure external subnet
[ 1] ext-1 - External interface
[ 2] 10gige-1 - External interface
[Enter] Exit configuring external network.
Configure external subnet >>> [Enter]
配置时间
Configure cluster date and time
[ 1] Configure time zone
[ 2] Configure day and time
[Enter] Keep the current date and time: 2021/04/14 07:16:12 UTC.
Configure date >>> 1
Configure cluster time zone
[ 1] Greenwich Mean Time
[ 2] Eastern Time Zone
[ 3] Central Time Zone
[ 4] Mountain Time Zone
[ 5] Pacific Time Zone
[ 6] Arizona
[ 7] Alaska
[ 8] Hawaii
[ 9] Japan
[10] Advanced
[Enter] Keep current time zone: Greenwich Mean Time
Configure time zone >>> 5
Pacific Time Zone
Configure cluster date and time
[ 1] Configure time zone
[ 2] Configure day and time
[Enter] Keep the current date and time: 2021/04/14 00:16:26 PDT.
Configure date >>> 2
Type new date and time values
or press [Enter] to keep the current date and time: 2021/04/14 00:16:33 PDT.
Configure time >>> 2021/04/14 15:19:00
Configure cluster date and time
[ 1] Configure time zone
[ 2] Configure day and time
[Enter] Keep the current date and time: 2021/04/14 15:19:00 PDT.
Configure date >>> [Enter]
配置集群加入模式，默认手动
Configure cluster join mode
[ 1] Manual
[ 2] Secure
[Enter] Keep the current join mode: Manual
Configure join mode >>> [Enter]
Join mode set to Manual.
确认信息
You have made the following configuration changes:
Cluster name : (not set) -> Lxyy-isilon
Encoding : (not set) -> utf-8
int-a : enabled -> enabled
int-a netmask : (not set) -> 255.255.255.0
int-a IP ranges : (not set) -> { 10.0.1.1-10.0.1.254 }
int-b : disabled -> enabled
int-b netmask : (not set) -> 255.255.255.0
int-b IP ranges : (not set) -> { 10.0.2.1-10.0.2.254 }
lpbk : disabled -> enabled
lpbk netmask : (not set) -> 255.255.255.0
lpbk IP ranges : (not set) -> { 10.0.3.1-10.0.3.254 }
10gige-1 netmask : (not set) -> 255.255.255.0
10gige-1 IP range : (not set) -> { 192.168.12.60-192.168.12.70 }
10gige-1 gateway : (not set) -> 192.168.12.254
SmartConnect zone name : (not set) -> isilon.lxyy.com
SmartConnect service IP: (not set) -> 192.168.12.88
DNS servers : (not set) -> { 192.168.18.1 }
Search domains : (not set) -> { lxyy.com }
Do you wish to commit these changes? [yes]
Commit changes? >>> yes
等待完成初始化……
4.加入新的 Isilon 节点
通过串口线连接新结点加入现有集群，也可以使用Web administration登录集群中任何一节点将新结点加入集群，只要节点能够通过Infiniband与集群通信，集群就可以识别新结点；下面将使用串口扩充集群。
Please select an option.
Node build: Isilon OneFS v8.2.2.0 B_8_2_2_016(RELEASE)
Node serial number: JWXNT183800140
Select an option:
[ 1] Create a new cluster
[ 2] Join an existing cluster
[ 3] Exit wizard and configure manually
[ 4] Reboot into SmartLock Compliance mode
Wizard >>> 2
等待加入节点，初始化完成。
第三个节点同样操作。
在浏览器输入SmartConnect IP 或IP pool中的任意IP即可登陆Isilon Administration：
