BENTLY 3500/42M 176449-02 前置器地震监测器为四通道
3500/42M前置器地震监测器：
l通过不断比较来保护机器
根据配置的警报监测参数
驱动警报的设置点。
l向双方传达重要的机器信息
操作和维护人员。
3500/42M前置器地震监测器为四通道
接受近距离和地震输入的监测器
传感器。它调节信号以提供振动和
位置测量并比较条件
带有用户可编程报警的信号。
您可以使用3500机架对每个通道进行编程
监控和报告的配置软件：
-径向振动-REBAM-推力
位置
-加速度-胀差-轴
完全的
-偏心度-圆形验收
区域-速度
OK发光二极管
指示何时
3500/42M前置器
地震监测器
操作正常。
发送/接收LED
指示何时
3500/42M前置器
地震监测器
与…沟通
3500中的其他模块
支架
旁路LED
指示何时
3500/42M前置器
地震监测器处于
旁路模式。
缓冲的
传感器
输出
每个显示器的前部
有一个同轴连接器
对于每个通道。
每个连接器都有短路保护。
输出
阻抗550Ω
传感器
电源-24 Vdc
录音机
+4至+20毫安
数值与
监视器满刻度。
显示器提供
单个记录器值
对于每个通道。
监视器操作
不受短路影响
记录器上的电路
输出。
电压
顺从
（电流输出）
0至+12 Vdc范围
负载
负载电阻为0至600Ω.
The 3500/42M Proximitor Seismic Monitor:
l Protects machinery by continuously comparing
monitored parameters against configured alarm
setpoints to drive alarms.
l Communicates essential machine information to both
operations and maintenance personnel.
The 3500/42M Proximitor Seismic Monitor is a four-channel
monitor that accepts input from proximity and seismic
transducers. It conditions the signal to provide vibration and
position measurements and compares the conditioned
signals with user-programmable alarms.
You can program each channel using the 3500 Rack
Configuration Software to monitor and report:
- Radial vibration - REBAM - Thrust
position
- Acceleration - Differential expansion - Shaft
absolute
- Eccentricity - Circular acceptance
region - Velocity
OK LED
Indicates when the
3500/42M Proximitor
Seismic Monitor is
operating properly.
TX/RX LED
Indicates when the
3500/42M Proximitor
Seismic Monitor is
communicating with
other modules in the 3500
rack.
Bypass LED
Indicates when the
3500/42M Proximitor
Seismic Monitor is in
Bypass Mode.
Buffered
Transducer
Outputs
The front of each monitor
has one coaxial connector
for each channel.
Each connector is shortcircuit protected.
Output
Impedance 550 Ω
Transducer
Power Supply -24 Vdc
Recorder
+4 to +20 mA
Values are proportional to
monitor full-scale.
The monitor provides
individual recorder values
for each channel.
Monitor operation is
unaffected by short
circuits on recorder
outputs.
Voltage
Compliance
(current output)
0 to +12 Vdc range across
load
Load resistance is 0 to 600Ω.
