ABB ASFC-01C 装置附带的空气挡板固定到顶部模块导轨上
从“文件”菜单下载DriveAP应用程序到RMIO板！开放区块
应用程序文件（*.ap）。从驱动器菜单执行下载。启动已使用的
DriveAP的时间级别。
减少运行功能可用于并联连接的R8逆变器，
2Ö12×R8i。减少运行功能，可以继续
如果逆变器模块出现故障，则在有限电流下运行。如果其中一个
模块损坏，必须将其从机柜中取出。参数
需要改变以在电流减少的情况下继续运行。
•必须遵守安全说明。请参阅上的安全说明
适当硬件手册或安全手册的首页。
•从驱动器上断开电源电压和所有辅助电压。
•从机柜中取出损坏的逆变器模块。参见适当内容
硬件手册。
•将装置附带的空气挡板固定到顶部模块导轨上，以
阻挡气流通过空的模块空间。
•禁用隔离模块的充电监控，即设置开关
ASFC-01板的S1ÖS3连接到DIS（=禁用）。
•打开电源电压。INT CONFIG故障（09.06故障字3位7
值为1）现在表示连接的逆变器的数量
模块已更改。
•如果在有限的电流下继续操作，则现有的
逆变器模块必须通过参数16.10 INT CONFIG USER进行设置。
•重置故障并启动驱动器。PPCS链接自动重新配置
并且最大电流在
与新逆变器配置和逆变器标称电流的关系。
注意：如果INT CONFIG故障再次出现，则并联连接的数量
参数16.10 INT CONFIG USER定义的逆变器不正确。看见
信号08.22 INT CONFIG WORD（内部配置字）。
Download DriveAP application to RMIO board from File menu ! Open block
application file (*.ap). Perform Download from Drive menu. Start the used
time levels by DriveAP.
Reduced run function is available for parallel connected R8 inverters,
2Ö12 × R8i. Reduced run function makes it possible to continue the
operation with limited current if an inverter module(s) is out of order. If one of
the modules is broken, it must be removed from the cabinet. Parameter
change is needed to continue the run with reduced current.
• The safety instructions must be followed. See the safety instructions on
the first pages of the appropriate hardware manual or the safety manual.
• Disconnect the supply voltage and all auxiliary voltages from the drive.
• Remove the broken inverter module from the cabinet. See appropriate
hardware manual.
• Fasten the air baffle provided with the unit to the top module guide to
block airflow through the empty module space.
• Disable the charging monitoring of the isolated module, i.e. set switch
S1ÖS3 of the ASFC-01 board to DIS (=disabled).
• Switch on the supply voltage. INT CONFIG fault (09.06 Fault Word 3 bit 7
value is 1) now indicates that the number of the connected inverter
modules has changed.
• If the operation is continued with limited current, number of existing
inverter modules must be set by parameter 16.10 INT CONFIG USER.
• Reset the fault and start the drive. PPCS link is reconfigured automatically
and the maximum current is limited (20.04 MAXIMUM CURRENT) in
relation to the new inverter configuration and inverter nominal current.
Note: If INT CONFIG fault reappears, the number of parallel connected
inverters defined by parameter 16.10 INT CONFIG USER is incorrect. See
signal 08.22 INT CONFIG WORD.
